Sten - Sten Gun

The STEN (or Sten gun) was a family of British submachine guns chambered in 9×19mm and used extensively by British and Commonwealth forces throughout World War II and the Korean War. They were notable for having a simple design and very low production cost making them effective insurgency weapons for resistance groups.

STEN is an acronym, from the names of the weapon's chief designers, Major Reginald V. Shepherd and Harold Turpin, and EN for Enfield. Over four million Stens in various versions were made in the 1940s.

History

The Sten emerged while Britain was engaged in the Battle of Britain, facing invasion by Germany. The army was forced to replace weapons lost during the evacuation from Dunkirk while expanding at the same time. Prior to 1941 (and even later) the British were purchasing all the Thompson submachine guns they could from the United States, but these did not meet demand. The American entry into the war at the end of 1941 placed an even bigger demand on the facilities making Thompsons. In order to rapidly equip a sufficient fighting force to counter the Axis threat, the Royal Small Arms Factory, Enfield, was commissioned to produce an alternative.

The credited designers were Major R. V. Shepherd, OBE, Inspector of Armaments in the Ministry of Supply Design Department at The Royal Arsenal, Woolwich, (later Assistant Chief Superintendent at the Armaments Design Department) and Mr. Harold John Turpin, Senior Draughtsman of the Design Department of the Royal Small Arms Factory (RSAF), Enfield. Shepherd had been recalled to service after having retired and spending some time at BSA.

The Sten shared design features, such as its side-mounted magazine configuration, with the Royal Navy's Lanchester submachine gun, which was a copy of the German MP28. In terms of manufacture, the Lanchester was entirely different, being made of high-quality materials with pre-war fit and finish, in stark contrast to the Sten's austere execution. The Lanchester and Sten magazines were even interchangeable (though the Lanchester's magazine was longer with a 50-round capacity, compared to the Sten's 32-round capacity).

The Sten used simple stamped metal components and minor welding, which required minimal machining and manufacturing. Much of the production could be performed by small workshops, with the firearms assembled at the Enfield site. Over the period of manufacture the Sten design was further simplified: the most basic model, the Mark III, could be produced from five man-hours of work. Some of the cheapest versions were made from only 47 different parts. It was distinctive for its bare appearance (just a pipe with a metal loop for a stock), and its horizontal magazine. The Mark I was a more finely finished weapon with a wooden foregrip and handle; later versions were generally more spartan, although the final version, the Mark V, which was produced after the threat of invasion had died down, was produced to a higher standard.

The Sten was highly unreliable, prone to jamming, and inaccurate beyond 30 meters. It was unsuitable for guerrilla operations in open country because it encouraged waste of ammunition. But it was easy and cheap to produce â€" a gun was said to cost fifteen shillings (three quarters of a pound) â€" and was supplied to the (French) Resistance in huge quantities.

The Sten underwent various design improvements over the course of the war. For example, the Mark 4 cocking handle and corresponding hole drilled in the receiver were created to lock the bolt in the closed position to reduce the likelihood of accidental discharges inherent in the design. Most changes to the production process were more subtle, designed to give greater ease of manufacture and increased reliability. Build quality ranged from quite good (Canadian production) to poor (early British production.) Sten guns of late 1942 and beyond were, in general, highly effective weapons, though complaints of accidental discharge continued throughout the war. Such was the ease of manufacture that the Germans also produced a version of the Sten, the MP 3008, late in the war and the Sten was used extensively by Jewish partisans during the Israeli War of Independence

The Sten was replaced by the Sterling submachine gun from 1953 and was gradually withdrawn from British service in the 1960s. The other Commonwealth nations made or adopted their own replacements.

Design

The Sten was a blowback-operated submachine gun firing from an open bolt with a fixed firing pin on the face of the bolt. This means the bolt remains to the rear when the weapon is cocked, and on pulling the trigger the bolt flies forward under spring pressure, stripping the round from the magazine, chambering it and firing the weapon all in the same movement. There is no breech locking mechanism, the rearward movement of the bolt caused by the recoil impulse is arrested only by the mainspring and the bolt's inertia. The basic operating principles were similar to those of the German MP40, Russian PPSh-41, US M3 submachine gun and numerous other designs. These shared similar attributes and faults; they were simple and cheap to manufacture, and put an automatic weapon into the hands of soldiers, greatly increasing the short-range firepower of the infantry, especially when the main infantry weapon was a bolt-action rifle capable of only around 15 rounds per minute and not suited for short-range combat. However, the open-bolt firing and use of pistol ammunition severely restricted accuracy, with an effective range of around 100m.

Stoppages could occur due to a variety of problems: some as a result of poor maintenance, while others were particular to the Sten. Carbon buildup on the face of the breech or debris in the bolt raceway could cause a failure to fire, while a dirty chamber could cause a failure to feed. Firing the Sten by grasping the magazine with the supporting hand tended to wear the magazine catch, altering the angle of feed and causing a failure to feed - the correct method of holding the weapon was as with a rifle, the left hand cradling the fore piece, as per the picture of Winston Churchill firing one below.

Additional problems stemmed from the Sten's magazine, which was a direct copy of the one used in the German MP-38, originally in order to facilitate the use of German 9 mm magazines. Unfortunately, this decision necessarily incorporated the Erma magazine's faults in the process. The magazine had two columns of 9 mm cartridges in a staggered arrangement, merging at the top to form a single column. While other staggered magazines, such as the Thompson, fed from both the left and right side alternately (double-column, double feed), the Sten magazine, like the MP38, required the cartridges to gradually merge at the top of the magazine to form a single column (double column, single feed). As a consequence, any dirt or foreign matter in this taper area could cause feed malfunctions. Additionally, the walls of the magazine lip had to endure the full stresses of the rounds being pushed in by the spring. This, along with rough handling could result in deformation of the magazine lips (wh ich required a precise 8° feed angle to operate), resulting in misfeeding and a failure to fire.

Modern 9 mm magazines, such as those used by the Sterling SMG, are curved and feed both sides to avoid this problem. If a Sten failed to feed due to jammed cartridges in the magazine, standard practice to clear it was as follows: remove magazine from Sten, tap the base of the magazine against the knee, re-insert magazine in Sten, then recocking the weapon and firing again as normal. To facilitate easier loading when attempting to push the cartridges down to insert the next one, a magazine filler tool was developed and formed part of the weapon's kit.

The slot on the side of the body where the cocking knob ran was also a target of criticism, as the long opening could allow foreign objects to enter. On the other hand, a beneficial side-effect of the Sten's minimalist design was that it would fire without any lubrication. This proved useful in desert environments such as the Western Desert Campaign, where oil attracted and retained dust and sand.

The open bolt design combined with cheap manufacture and rudimentary safety devices also meant the weapon was prone to accidental discharges, which proved hazardous. A simple safety could be engaged while the bolt was in the rearwards (cocked) position. However, if a Sten with a loaded magazine, with the bolt in the closed position, was dropped or the butt was knocked against the ground, the bolt could move far enough rearward to pick up a round (but not far enough to be engaged by the trigger mechanism) and the spring pressure could be enough to chamber and fire the round. The Mk 4 cocking handle was designed to prevent this by enabling the bolt to be locked in its forward position, thereby immobilising it. Wear and manufacturing tolerances could render these safety devices ineffective.

Variants

Sten guns were produced in several basic marks (though the Mk I saw limited service, and the Mk IV was never issued), and nearly half of the total produced were Mark II versions. Approximately 4.5 million Stens were produced during the war.

Mark I

The first ever Mk I Sten gun (number 'T-40/1' indicating its originator Harold Turpin, the year 1940 and the serial number "1") was handmade by Turpin at the Philips Radio works at Perivale, Middlesex during December 1940/January 1941. This particular weapon is held by the historical weapons collection of the British Army's Infantry and Small Arms School Corps in Warminster, Wiltshire.

The first model had a conical flash hider and fine finish. It had a wooden foregrip and forward handle (sometimes this was made of steel), as well for a section of the stock. The stock was a small tube outline, rather like the Mark II Canadian. One unique feature was that the front pistol grip could be rotated forward to make the firearm easier to stow. The barrel sleeve extended all the way to the end, where it met the flash hider. Along the top of the tube surrounding the barrel was a line of small holes and its sights were configured somewhat differently. About 100,000 were made before production switched to the Mark II. Sten Mk I's in German possession were designated MP 748(e), the 'e' standing for englisch.

Mark I*

This was the first simplification of the Mk I. The foregrip, the wooden furniture and the flash hider were removed for production expediency.

Mark II

The Mark II was the most common variant, with two million units produced. It was a much rougher weapon than the Mk I. The flash eliminator and the folding handle (the grip) of the Mk I were eliminated. A removable barrel was now provided which projected 3 inches (76 mm) beyond the barrel sleeve. Also, a special catch allowed the magazine to be slid partly out of the magazine housing and the housing rotated 90 degrees counter-clockwise (from the operator's perspective), together covering the ejection opening and allowing the weapon and magazine both to lie flat on its side.

The barrel sleeve was shorter and rather than having small holes on the top, it had three sets of three holes equally spaced on the shroud. To allow a soldier to hold a Sten by the hot barrel sleeve with the supporting hand, an insulating lace-on leather sleeve guard was sometimes issued. Sten Mk II's in German possession were designated MP 749(e). Some MkIIs were fitted with a wooden stock as this part was desirable and interchangeable with the Mk V. Also, the Spz-kr assault rifle uses the receiver and components from the Sten Mk II.

Regular Mark II:

• Overall length: 762 mm (30.0 in)
• Barrel length: 197 mm (7.8 in)
• Weight: 3.2 kg (7.1 lb)

Mark II (Canadian)

During World War II a version of the Sten gun was produced at the Long Branch Arsenal in Long Branch, Ontario now part of Toronto, Ontario. This was very similar to the regular Mark II, with a different stock ('skeleton' type instead of strut type) and improved quality of manufacture. It was first used in combat in the Dieppe Raid in 1942.

Mark II:

• Overall length: 896 mm (35.3 in)
• Barrel length: 198 mm (7.8 in)
• Weight: 3.8 kg (8.4 lb)

Mark III

This simple design was the next most commonly produced after the Mark II. It was a simplification of the Mk I made both in Canada and the UK. Lines Bros Ltd was the largest manufacturer. The biggest difference from the Mark II was the unification of the receiver, ejection port, and barrel shroud that now extended farther up the barrel. The barrel was fixed and the body was welded shut along the centre of the top. Captured Sten Mk IIIs in German possession were designated MP 750(e).

Mark V

Introduced in 1944, the Mk V was essentially a better-quality, more elaborate version of the Mk 2. Changes included a wooden pistol grip, a vertical wooden fore grip, a wooden stock, and a bayonet mount. There was a No4 Leeâ€"Enfield foresight and the weapon was of better quality manufacture and finish than the Mk2 and Mk3. The Sten bandolier issued to paratroopers held seven full magazines.

Another variant of the Mk V had a swivel stock and rear sight mirror intended for firing around corners in urban warfare, similar to the Krummlauf developed by the Germans for the StG 44.

Mark VI

• Overall length: 908 mm (35.7 in)
• Barrel length: 198 mm (7.8 in)
• Weight: 4.5 kg (9.9 lb)

Suppressed models

Mk IIS and Mk VI models incorporated an integral suppressor ("silencer") and had a lower muzzle velocity than the others due to a ported barrel intended to reduce velocity to below the speed of sound; 305 m/s (1,001 ft/s). The suppressor would heat up rapidly when the weapon was fired and a canvas cover was laced around the suppressor for some protection for the firer's supporting hand.

Mk IIS

The Mk IIS was, as the name suggests, a suppressed version of the Mk II. Captured examples of the Sten Mk IIS in German service were designated MP 751(e).

Mk VI

The Mk VI (or '6') was a suppressed version of the Mk V. The Mk VI was the heaviest version due to the added weight of the suppressor, as well as using a wooden pistol grip and wooden stock.

The suppressed models were produced at the request of the Special Operations Executive (SOE) for use on clandestine operations in occupied Europe, starting with the Mk IIS in 1943. Owing to their tendency to overheat, they were fired in short bursts or single shots.

In addition to its use in the European Theatre, the Mk IIS saw service with clandestine units in the Southwest Pacific Area (SWPA) such as the Services Reconnaissance Department and SOE's Force 136 on operations against Imperial Japanese forces. The Sten Mk IIS was used by the Operation Jaywick party during their raid into Japanese-occupied Singapore Harbour.

The Sten Mk IIS also saw service with the Australian Special Air Service (SAS) in Vietnam.

Experimental models

Mark II (wooden butt model)

This was a standard Sten Mk.II submachine gun with a wooden butt attached in place of the wireframe steel butt used with Mk.IIs. This wooden butt model was never put in service, likely due to the cost of producing it.

Mark II (Rosciszewski model)

This was a Sten Mk.II modified by Antoni Rosciszewski of Small Arms Ltd. The magazine was mechanically operated by the breech block movement. The trigger was split into two sections, with the upper part of the trigger offering full-auto fire and a lower part offering single shots. It was very complex in design and never fielded.

Mark II (pistol grip model)

This was a Sten Mk.II with a wireframe pistol grip, intended for use with paratroopers. It was compact but predictably uncomfortable to fire.

Model T42

This was a Sten Mk.II modified with a 5-inch barrel and folding stock, as well as a conventional pistol grip and redesigned trigger guard. It was dubbed the "T42" in prototype phases, but never entered service.

Mark III (wooden model)

This was a Sten Mk.III with a "Lanchester" type wooden body and butt, and bayonet fittings. Sling swivels were also added. It never entered service due to the costs associated with producing it.

Mark III (wooden model II)

This was a Sten Mk.III entirely encased in a wooden body, with the only external metal parts being the trigger, barrel, magazine and cocking handle. The trigger and pistol grip were in line with the magazine. The reasons for its creation are likely an experiment into increasing the comfort and handling of the weapon in freezing temperatures.

Mark IV

The Mark IV was a smaller version which did not progress beyond the prototype stage. It was near pistol-sized and it had a different configuration with a conical flash hider, a rear pistol grip, a very light stock and a much shorter barrel.

Rofsten

Developed at the Royal Ordnance Factory at Fazakerley (ROF), the Rofsten was an odd Sten prototype with a redesigned magazine feed, ergonomic pistol grip, selector switch and cocking system. The weapon was cocked by pulling the small ring above the stock. A large flash eliminator was fixed onto the barrel, and a No.5 bayonet could be fixed. It was made to a very high quality standard and had an increased rate of fire (around 900 rounds per minute). The Rofsten was made in 1944 as a single prototype and ROF wanted to submit it to trials the next year. Despite better quality there were numerous reliability problems due to the much higher rate of fire. The budget cuts prevented the modifications and this version never got beyond the prototype stage.

Foreign-built variants and post 1945 derivatives

Argentine Sten

Sten MkIIs were licence-copied in Argentina by Pistola Hispano Argentino and can be recognised with a wooden handguard in front of the trigger group. It was known as the Modelo C.4. Another variant came with a pistol grip section based on the Ballesterâ€"Molina .45 pistol.

Palestininian Mandate Stens

Copies of the Sten Mk II and Sten Mk V were clandestinely manufactured in Tel Aviv and on various kibbutzim in 1945-48 for use with Haganah and other Jewish paramilitary groups. According to British paratroopers who served in the Palestine Mandate in 1946-47, the Sten copies were found to be of better quality than their own issued weapons.

French Sten

The French "Gnome et Rhône" R5 Sten, manufactured by the motorbike and aeroplane engine manufacturer Gnome et Rhône (SNECMA), came with a forward pistol grip and distinctive wooden stock, although its greatest improvement was a sliding bolt safety, added to secure the bolt in its forward position.

Another variant made by MAC (Manufacture d’armes de Châtellerault), were made and tested shortly after WWII. One variant had an unusual stock shape that proved detrimental to the firer’s aim. Internally it was basically a Sten gun but had two triggers for semi/full auto, a grip safety and a foregrip that used MP40 magazines. Another had a folding stock with a folding magazine insert. The trigger mechanism was complicated and unusual. Neither of these prototypes had any kind of success and MAC closed its doors not long after their conception. The French were not short of SMGs after the war; they had some 3,750 Thompsons and Stens, as well as MAS 38s.

Norwegian Sten

In German-occupied Norway the resistance, under the leadership of Bror With, created a large number of Sten guns from scratch, mainly to equip members of the underground army Milorg. In his autobiography, Norwegian resistance fighter Max Manus frequently mentions the Sten as one of the weapons his groups of commandos and resistance fighters used effectively against German troops.

Danish Sten

Several groups in the Danish resistance movement manufactured Sten guns for their own use. BOPA produced around 200 in a bicycle repair shop on Gammel Køge landevej (Old Køge road), south of Copenhagen. Holger Danske produced about 150 in workshops in Copenhagen, while employees of the construction company Monberg & Thorsen built approximately 200 - 300 in what is now the municipality of Gladsaxe (a suburb of Copenhagen) for use by Holger Danske and others. The resistance groups 'Frit Danmark' and 'Ringen' also built significant numbers of Stens.

Polish Sten

The Polish resistance was provided with numerous Stens of various models by the SOE and the Cichociemni. Between 1942 and 1944, approximately 11,000 Sten Mk IIs were delivered to the Armia Krajowa. Due to the simplicity of design, local production of Sten variants was started in at least 23 underground workshops in Poland. Some of them produced copies of Mark IIs, while others produced the so-called Polski Sten and KIS. The Polski Stens made in Warsaw under the command of Ryszard Białostocki were built from a number of "legal" elements made in official factories or acquired through other means. The main body of the machine pistol was made from hydraulic cylinders produced for hospital equipment. All the machine pistols were marked in English to disguise their origin. Stens' barrels were also used for SMGs produced in Poland under the name Błyskawica.

Belgian Sten MkII

A little known version of the MkII Sten was built in Belgium by l'arsenale militare belga (the Belgian military arsenal). The magazine well was stamped AsArm (the manufacturer), ABL (for Armée Belge Belgisch Leger), the Belgian Royal Crown and a serial number of typically five figure with no letter prefix. It is believed the Belgian built Mk II Stens remained in ABL service until the early 1980s, particularly with helicopter-borne forces. Some of the weapons had a "Parkerised" finish.

Gerät Potsdam

In late 1944, the Mauser works in Germany secretly started manufacturing copies of the Mk II Sten, apparently for deception and sabotage purposes. These weapons were intended to duplicate the British original as closely as possible, including the markings. The series was referred to as the Gerät Potsdam (Potsdam Device) and approximately 28,000 weapons were made â€" even though the Germans had ample stocks of captured original Stens available. The intended purpose of these copies is now uncertain.

MP 3008

In early 1945, Germany was seeking a cheap version of the MP40 machine pistol for the Volkssturm. For that purpose a modified Sten was designed by Mauser and named the MP 3008. The main difference was the magazine attached below the weapon. Altogether, roughly 10,000 pieces were produced before the end of World War II.

Austen Mk I

The Mark I Austen (from "Australian Sten") was a 9mm Australian submachine gun derived from the British Sten gun developed during the Second World War by the Lithgow Small Arms Factory. It externally resembled the Sten but had twin pistol grips and folding stock resembling those of the German MP40. A Mk 2 version was also produced which was of different appearance and which made more use of die-cast components. Although 20,000 were made, the Austen never achieved the success of the competing Australian-designed Owen submachine gun, known as the "Owen Gun".

Imperia submachine gun

After the Second World War the Belgian Army was mainly equipped with a mixture of British and American submachine guns. The army, wanting to replace them with a modern and preferably native design, tested various designs with the Vigneron M2 and licence-produced FN Uzi being selected. However, the Imperia was an improved Sten with a fire selector and retractable stock.

Sputter Gun

A short-lived American invention developed in the 1980s, the Sputter Gun was designed to circumvent the law that defined a machine gun as something that fired multiple rounds with one pull of the trigger. The Sputter Gun had no trigger, but fired continuously after loading and the pulling back of its bolt, firing until it ran out of ammunition. The gun was very short lived as the ATF quickly reclassified it.

Halcon ML-57

The Halcon ML-57 was a simpler derivative of the Sten gun of Argentine origin that was fed from a vertically inserted magazine.

International Ordnance MP2

During the 1970s-1980s, International Ordnance of San Antonio, Texas, USA released the MP2 machine pistol. It was intended as a more compact, simpler derivative of the British Sten gun to be used in urban guerrilla actions, to be manufactured cheaply and/or in less-than-well-equipped workshops and distributed to "friendly" undercover forces. Much like the FP-45 Liberator pistol of World War II, it could be discarded during an escape with no substantial loss for the force's arsenal. The MP2 is a blowback-operated weapon that fires from an open bolt with an extremely high rate of fire.

Cellini Dunn SM-9

The SM-9 is a machine pistol of Guatemalan origin and manufactured by Cellini-Dunn IMG, Military Research Corp and Wildfire Munitions as the SM-90. It is blowback operated, firing from an open bolt and can use magazines from Ingram MAC-10 submachine guns inserted into a similar foregrip that can be rotated 45 and 90 degrees for left/right handed operators. The layout of the receiver is somewhat simpler than that of a Sten with its internal components light in weight enabling a very high rate of fire of 1200rpm. Its forward pistol grip can hold a spare magazine as well as handling the weapon when firing.

Pleter 91

The Pleter submachine gun was created in 1991 when the breakup of Yugoslavia in the midst of emerging war left the newly formed Republic of Croatia with small number of military firearms. Since the embargo prevented the Croatian military from legally buying them on open market (so they were mostly obtained on the world black market, but with significantly higher price and sometimes of questionable quality), to fulfill the immediate need for arms, they tried to resort on quick and simple locally made designs.

Despite having a vertical magazine well (designed to accept 32-round double-feed direct copy of UZI magazine, rather than original single-feed Sten-type magazine), analogies with the Sten include a striking resemblance in the barrel assembly and in the bolt and recoil spring. In addition, this gun also fires from an open bolt, and is further simplified by removing fire mode selector or any safety.

SaskSten

SMG International in Canada manufactured reproductions of the Sten in six variants. They made copies of the Sten's Mk 1*, Mk II and Mk III, a "New Zealand Sten" (a Mk II/III Sten hybrid, with sights and a fixed magazine housing similar to the Mk III), then branched out into "hypothetical" Sten-guns with a "Rotary Magazine Sten" (a Mk II Sten with a drum magazine attached below the weapon and wooden horizontal forward grip on the left side of the weapon) and the "FRT Gun" (a long barrel Sten with a wooden or Mk 1* type butt stock, a drum magazine attached below the weapon and sliding ramp rear sights). These last two being obviously not Sten reproductions, especially if they included a drum magazine. The "Rotary Magazine Sten" is a vertically fed Sten which uses a modified Sten bolt, which can use either PPSh drum magazines or stick magazines. The FRT gun is essentially a Suomi that uses a Sten trigger mechanism. All SaskSten guns fire from an open bolt.

Service

The Sten, especially the Mark II, tended to attract affection and loathing in equal measure. Its peculiar appearance when compared to other firearms of the era, combined with sometimes questionable reliability made it unpopular with some front-line troops. It gained nicknames such as "Plumber's Nightmare", "Plumber's Abortion", or "Stench Gun". The Sten's advantage was its ease of mass-production manufacture in a time of shortage during a major conflict.

Made by a variety of manufacturers, often with subcontracted parts, some early Sten guns were made poorly and/or not made to specification, and could malfunction in operation, sometimes in combat. The double-column, single-feed magazine copied from the German MP28 was never completely satisfactory, and hasty manufacturing processes often exacerbated misfeed problems inherent in the design. A common statement heard from British forces at the time was that the Sten was made "by Marks and Spencer out of Woolworth." British and Commonwealth forces in the early years of the war often extensively test-fired their weapons in training to weed out bad examples; a last-minute issue of newly manufactured Stens prior to going into action was not always welcomed.

The MK II and MK III Stens were regarded by many soldiers as very temperamental, and could accidentally discharge if dropped or even laid on the ground whilst the gun was cocked. Others would fire full-automatic when placed on 'single', or fire single shots when placed on 'automatic'. This was particularly true of early Stens using bronze bolts, where the sear projection underneath the bolt could wear down more easily than ones made of case-hardened steel.

Stens could jam at inopportune moments. One of the more notable instances of this was the assassination of SS-Obergruppenführer Reinhard Heydrich on 27 May 1942, when a Czechoslovak soldier â€" Warrant Officer Jozef Gabčík â€" fired his Sten point blank at Heydrich, only to have it misfire. His comrade Jan KubiÅ¡ then hastily tossed a grenade, which mortally wounded Heydrich. There are other accounts of the Sten's unreliability, some of them true, some exaggerated and some which are apocryphal. France manufactured (well-made) Sten copies postwar into the early 1950s, evidently believing in the basic reliability and durability of the design.

A well-maintained (and properly-functioning) Sten gun was a devastating close-range weapon for sections previously armed only with bolt-action rifles. In addition to regular British and Commonwealth military service, Stens were air-dropped in quantity to resistance fighters and partisans throughout occupied Europe. Due to their slim profile and ease of disassembly/reassembly, they were good for concealment and guerrilla warfare. Wrapping the barrel in wet rags would delay undesirable overheating of the barrel Guerrilla fighters in Europe became adept at repairing, modifying and eventually scratch-building clones of the Sten (over 2,000 Stens and about 500 of the similar BÅ‚yskawica SMGs were manufactured in occupied Poland).

Canadian infantry battalions in northwest Europe retained spare Sten guns for special missions and the Canadian Army reported a surplus of the weapons in 1944. The Sten saw use even after the economic crunch of World War II, replacing the Royal Navy's Lanchester submachine guns into the 1960s, and was used in the Korean War, including specialist versions for British Commandos. It was slowly withdrawn from British Army service in the 1960s and replaced by the Sterling SMG; Canada also phased out Sten, replacing it with the C1 SMG.

The Sten was one of the few weapons that the State of Israel could produce domestically during the 1948 Arabâ€"Israeli War. Even before the declaration of the State of Israel, the Yishuv had been producing Stens for the Haganah; after the declaration, Israel continued making Stens for IDF use. The opposing side also used (mostly British-made) Stens, particularly the irregular and semi-regular Arab Liberation Army.

In the 1950s "L numbering" came into use in the British Army for weaponsâ€"Stens were then known as L50 (Mk II), L51 (Mk III) and L52 (Mk V).

One of the last times the Sten was used in combat during British service was with the RUC during the IRA border campaign of 1956â€"1962. In foreign service, the Sten was used in combat at least as recently as the Indo-Pakistani War of 1971.

In 1971 various marks of Stens were used by guerilla fighters during the Bangladesh Liberation War.

A number of suppressed Stens were in limited use by the US Special Forces during the Vietnam war, including c. 1971, by the United States Army Rangers.

In 1984, Indian prime minister Indira Gandhi was assassinated by two of her bodyguards, one of whom fired the entire magazine of his Sten at point-blank range.

In the Second Sino-Japanese War and the Chinese Civil War, both nationalists and communists used the Sten. Some Stens were converted by the communists to 7.62×25mm by using the magazine housing from a PPS to accept curved PPS magazines. An example of such a conversion is on display at the Imperial War Museum, London.

The Finnish Army acquired moderate numbers of Stens in the late 1950s, mainly Mk. III versions. Refurbishment at the Kuopio Arsenal included bluing of the arms. Stens in Finnish service saw limited usage by conscripts (notably combat swimmers) and were mostly stockpiled for use in a future mobilization.

During the Zapatista movement in 1994 some Zapatista soldiers were armed with Sten guns.

Users

Gallery

References

External links

• "Sten Gun to be forerunner of invasion" September 1943 detailed article in Popular Science
• Various high-resolution photos of the Sten Mk II, III and V
• How to field-strip a Sten
• Complete machinist's plans to manufacture a Sten Mk II
• Sten at Modern Firearms
• REME Museum
• Article on Silenced Sten
• STEN Variants
• MP3008
• Sten
• Imperia submachine gun